Sena PS810 Bedienungsanleitung Seite 85
- Seite / 110
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
85
InTimeExcds, OutTimeExcds :
Specifies the number of time-to-live (TTL) exceeded messages received or sent. A time-to-live
exceeded message is sent to the originating computer when a datagram is discarded because the
number of routers it has passed through exceeds its time-to-live value.
InParmProbs, OutParmProbs :
Specifies the number of parameter-problem messages received or sent. A parameter-problem
message is sent to the originating computer when a router or host detects an error in a datagram’s IP
header.
InSrcQuenchs, OutSrcQuenchs :
Specifies the number of source quench messages received or sent. A source quench request is sent
to a computer to request that it reduces its rate of packet transmission.
InRedirects, OutRedirects :
Specifies the number of redirect messages received or sent. A redirect message is sent to the
originating computer when a better route is discovered for a datagram sent by that computer.
InEchos, OutEchos :
Specifies the number of echo requests received or sent. An echo request causes the receiving
computer to send an echo reply message back to the originating computer.
NEchoReps, OutEchoReps :
Specifies the number of echo replies received or sent. A computer sends an echo reply in response to
receiving an echo request message.
InTimestamps, OutTimestamps :
Specifies the number of time-stamp requests received or sent. A time-stamp request causes the
receiving computer to send a time-stamp reply back to the originating computer.
InTimestampReps, OutTimestampReps :
Specifies the number of time-stamp replies received or sent. A computer sends a time-stamp reply in
response to receiving a time-stamp request. Routers can use time-stamp requests and replies to
measure the transmission speed of datagrams on a network.
InAddrMasks, OutAddrMasks :
Specifies the number of address mask requests received or sent. A computer sends an address mask
request to determine the number of bits in the subnet mask for its local subnet.
- HelloDevice Pro Series 1
- Copyright Information 2
- Trademark Information 2
- Notice to Users 2
- Technical Support 2
- Revision history 3
- Contents 4
- 5. System Administration 71 5
- 6. System Statistics 80 5
- 7. CLI Guide 89 5
- 1. Introduction 7
- 1.2. Package Check List 8
- 1.3. Product Specification 9
- MAC address 10
- Session 10
- Client/Server 10
- Table 1-1 Acronym Table 11
- 2. Getting Started 12
- 2.1.2. PS410/810 Panel Layout 13
- 2.2. Connecting The Hardware 14
- 2.2.3. Connecting The Power 17
- System console: 18
- Remote console: 18
- 9600 Baud rate 19
- Data bits 8 19
- Parity None 19
- Stop bits 1 19
- No flow control 19
- 2.2.6. Using Remote Console 21
- 3. Network Configuration 24
- IP address 25
- Subnet mask 25
- Default gateway 25
- Primary and Secondary DNS 25
- 3.1.2. Using DHCP 26
- 3.2. SNMP Configurations 27
- 3.2.4. Management Using SNMP 29
- 3.4. SMTP Configuration 31
- 3.5. IP Filtering 32
- Service 33
- Chain rule 33
- 3.7. Locating Server 35
- 3.8. NFS Server Configuration 37
- TCP keep-alive time: 38
- TCP “keep-alive” probes: 38
- TCP keep-alive intervals: 38
- 4. Serial Port Configuration 39
- TCP/UDP mode only 40
- TCP mode only 40
- 4.2.1. Port Enable/Disable 41
- 4.2.2. Port Title 42
- UDP mode 43
- Modem emulation mode 43
- Max. allowed connection 46
- Cyclic Connection 46
- Inactivity Timeout 46
- Socket ID 46
- TCP Nagle algorithm 46
- DTR/DSR behavior 47
- UDP receiving port 49
- (Verbose Code) 51
- * Not supported in PS810 53
- Command echo delay(ms) 55
- Default command echo 56
- Default data mode 56
- Init string 56
- 4.2.6. Serial Port Parameters 62
- Baud rate 63
- Data bits 63
- Parity 63
- Stop bits 63
- Flow control 64
- Inter-character timeout 64
- 4.2.7. Modem Configuration 65
- 4.2.8. Port Logging 67
- Port event handling 68
- Notification interval 68
- Email notification 68
- Subject of Email 68
- Recipient’s Email address 68
- 5. System Administration 71
- 5.3. Change Password 72
- 5.5. Date And Time Settings 73
- 5.6. Factory Reset 74
- 5.7. Configuration Management 74
- 5.8. Firmware Upgrade 76
- 5.9. User Administration 78
- 6. System Statistics 80
- 6.2. Serial Ports Statistics 81
- 6.3. IP Statistics 81
- ReasmOKs : 83
- ReasmFails : 83
- FragOKs : 83
- FragFails : 83
- FragCreates : 83
- 6.4. ICMP Statistics 84
- 6.5. TCP Statistics 86
- 6.6. UDP Statistics 88
- 7. CLI Guide 89
- 7.4. Accessing CLI 90
- 1 2 3 4 5 91
- HelloDevice 92
- Remote Host 92
- A 1.4. Serial Wiring Diagram 93
- A 2.1. port1.conf 95
- A 2.2. filter.conf 95
- A 2.3. snmp.conf 95
- A 4.1. Overview 98
- A 4.2. Main Menu 98
- A 4.3. RTC Configuration Menu 98
- A 4.4. Hardware Test Menu 99
- A 4.5. Firmware Upgrade Menu 102
- SSL enable = Enable 105
- Appendix 6. Warranty 109
Verwandte Produkte und Handbücher für Computerzubehör Sena PS810
Computerzubehör Sena PS210W Bedienungsanleitung
(104 Seiten)
(104 Seiten)
Computerzubehör Sena LS110 Bedienungsanleitung
(66 Seiten)
(66 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.301 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern