Sena PS810 Bedienungsanleitung Seite 46
- Seite / 110
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
46
For this purpose, SENA OEM version of Serial/IP from Tactical Software, LLC is bundled with Pro
Series. Please refer to documentations of Serial/IP for more detail information about using the COM
port redirector. (Please refer to section Appendix 5. Using Pro Series With Serial/IP for more detail
information)
Max. allowed connection
The Pro Series supports up to 8 multiple connections from external host(s) to the serial port. If there
are remote host connections by the remote host list configuration already, possible number of
connection will be reduced (Max. allowed connection - remote host(s) connected already). For
example, if user set Max. allowed connection as 8 and if there are 3 connections from Pro Series to
remote hosts, which are configured in the remote host list, then maximum number of connection from
external hosts to a serial port will be reduced to 5. For more detailed information for remote host list
configuration, please refer to 4.2.4. Remote Host Configuration section.
Cyclic Connection
If Cyclic Connection function is enabled, the Pro Series will make an attempt to connect to the user-
defined remote host(s) at a given interval even if there’s no incoming serial data from the device
connected to that serial port. If there is data on the remote host(s) to be sent to serial device, it can be
transferred to the serial device via Pro Series’ serial port after the connection is established. Eventually,
users can monitor the serial device periodically by making the remote host send the serial command
to the Pro Series whenever it is connected to the remote host. This option is useful when users need
to gather the device information periodically even if the serial device does not send its data periodically.
Figure 4-5 shows the State Transition Diagram of the session operations in TCP mode.
Inactivity Timeout
When Inactivity Timeout function is enabled, connection between remote host(s) and Pro Series will
be closed automatically if there is no data transmission during the value which is set in Inactivity
Timeout configuration.
Socket ID
When many Pro Series devices connect a same remote host(s), sometimes it is needed to identify the
device. In this case, Socket ID is available for identification of each device. Pro Series send the Socket
ID string before starting the data transmission. User can define Socket ID with a specific string. In TCP
mode, specified Socket ID strings are sent once at the time of establishing TCP connection.
TCP Nagle algorithm
Modern TCP implementations include a mechanism, known as the Nagle algorithm, which prevents
the unnecessary transmission of a large number of small packets. This algorithm has proved useful in
- HelloDevice Pro Series 1
- Copyright Information 2
- Trademark Information 2
- Notice to Users 2
- Technical Support 2
- Revision history 3
- Contents 4
- 5. System Administration 71 5
- 6. System Statistics 80 5
- 7. CLI Guide 89 5
- 1. Introduction 7
- 1.2. Package Check List 8
- 1.3. Product Specification 9
- MAC address 10
- Session 10
- Client/Server 10
- Table 1-1 Acronym Table 11
- 2. Getting Started 12
- 2.1.2. PS410/810 Panel Layout 13
- 2.2. Connecting The Hardware 14
- 2.2.3. Connecting The Power 17
- System console: 18
- Remote console: 18
- 9600 Baud rate 19
- Data bits 8 19
- Parity None 19
- Stop bits 1 19
- No flow control 19
- 2.2.6. Using Remote Console 21
- 3. Network Configuration 24
- IP address 25
- Subnet mask 25
- Default gateway 25
- Primary and Secondary DNS 25
- 3.1.2. Using DHCP 26
- 3.2. SNMP Configurations 27
- 3.2.4. Management Using SNMP 29
- 3.4. SMTP Configuration 31
- 3.5. IP Filtering 32
- Service 33
- Chain rule 33
- 3.7. Locating Server 35
- 3.8. NFS Server Configuration 37
- TCP keep-alive time: 38
- TCP “keep-alive” probes: 38
- TCP keep-alive intervals: 38
- 4. Serial Port Configuration 39
- TCP/UDP mode only 40
- TCP mode only 40
- 4.2.1. Port Enable/Disable 41
- 4.2.2. Port Title 42
- UDP mode 43
- Modem emulation mode 43
- Max. allowed connection 46
- Cyclic Connection 46
- Inactivity Timeout 46
- Socket ID 46
- TCP Nagle algorithm 46
- DTR/DSR behavior 47
- UDP receiving port 49
- (Verbose Code) 51
- * Not supported in PS810 53
- Command echo delay(ms) 55
- Default command echo 56
- Default data mode 56
- Init string 56
- 4.2.6. Serial Port Parameters 62
- Baud rate 63
- Data bits 63
- Parity 63
- Stop bits 63
- Flow control 64
- Inter-character timeout 64
- 4.2.7. Modem Configuration 65
- 4.2.8. Port Logging 67
- Port event handling 68
- Notification interval 68
- Email notification 68
- Subject of Email 68
- Recipient’s Email address 68
- 5. System Administration 71
- 5.3. Change Password 72
- 5.5. Date And Time Settings 73
- 5.6. Factory Reset 74
- 5.7. Configuration Management 74
- 5.8. Firmware Upgrade 76
- 5.9. User Administration 78
- 6. System Statistics 80
- 6.2. Serial Ports Statistics 81
- 6.3. IP Statistics 81
- ReasmOKs : 83
- ReasmFails : 83
- FragOKs : 83
- FragFails : 83
- FragCreates : 83
- 6.4. ICMP Statistics 84
- 6.5. TCP Statistics 86
- 6.6. UDP Statistics 88
- 7. CLI Guide 89
- 7.4. Accessing CLI 90
- 1 2 3 4 5 91
- HelloDevice 92
- Remote Host 92
- A 1.4. Serial Wiring Diagram 93
- A 2.1. port1.conf 95
- A 2.2. filter.conf 95
- A 2.3. snmp.conf 95
- A 4.1. Overview 98
- A 4.2. Main Menu 98
- A 4.3. RTC Configuration Menu 98
- A 4.4. Hardware Test Menu 99
- A 4.5. Firmware Upgrade Menu 102
- SSL enable = Enable 105
- Appendix 6. Warranty 109
Verwandte Produkte und Handbücher für Computerzubehör Sena PS810
Computerzubehör Sena PS210W Bedienungsanleitung
(104 Seiten)
(104 Seiten)
Computerzubehör Sena LS110 Bedienungsanleitung
(66 Seiten)
(66 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.459 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern