Sena PS810 Bedienungsanleitung PDF herunterladen (Seite 19)

Figure 2-14 Connecting a system console cable to the PS410

Figure 2-15 Connecting a system console cable to the PS810

2) Connect the other end of the cable to the serial port of the user’s computer.

3) Run a terminal emulator program (i.e. HyperTerminal). Set the serial configuration

parameters of the terminal emulation program as follows:

 9600 Baud rate

 Data bits 8

 Parity None

 Stop bits 1

 No flow control

4) Press the [ENTER] key.

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 109 110

HelloDevice Pro Series 1
Copyright Information 2
Trademark Information 2
Notice to Users 2
Technical Support 2
Revision history 3
Contents 4
5. System Administration 71 5
6. System Statistics 80 5
7. CLI Guide 89 5
1. Introduction 7
1.2. Package Check List 8
1.3. Product Specification 9
 MAC address 10
 Session 10
 Client/Server 10
Table 1-1 Acronym Table 11
2. Getting Started 12
2.1.2. PS410/810 Panel Layout 13
2.2. Connecting The Hardware 14
2.2.3. Connecting The Power 17
 System console: 18
 Remote console: 18
 9600 Baud rate 19
 Data bits 8 19
 Parity None 19
 Stop bits 1 19
 No flow control 19
2.2.6. Using Remote Console 21
3. Network Configuration 24
 IP address 25
 Subnet mask 25
 Default gateway 25
 Primary and Secondary DNS 25
3.1.2. Using DHCP 26
3.2. SNMP Configurations 27
3.2.4. Management Using SNMP 29
3.4. SMTP Configuration 31
3.5. IP Filtering 32
 Service 33
 Chain rule 33
3.7. Locating Server 35
3.8. NFS Server Configuration 37
 TCP keep-alive time: 38
 TCP “keep-alive” probes: 38
 TCP keep-alive intervals: 38
4. Serial Port Configuration 39
TCP/UDP mode only 40
TCP mode only 40
4.2.1. Port Enable/Disable 41
4.2.2. Port Title 42
 UDP mode 43
 Modem emulation mode 43
 Max. allowed connection 46
 Cyclic Connection 46
 Inactivity Timeout 46
 Socket ID 46
 TCP Nagle algorithm 46
 DTR/DSR behavior 47
 UDP receiving port 49
(Verbose Code) 51
* Not supported in PS810 53
 Command echo delay(ms) 55
 Default command echo 56
 Default data mode 56
 Init string 56
4.2.6. Serial Port Parameters 62
 Baud rate 63
 Data bits 63
 Parity 63
 Stop bits 63
 Flow control 64
 Inter-character timeout 64
4.2.7. Modem Configuration 65
4.2.8. Port Logging 67
 Port event handling 68
 Notification interval 68
 Email notification 68
 Subject of Email 68
 Recipient’s Email address 68
5. System Administration 71
5.3. Change Password 72
5.5. Date And Time Settings 73
5.6. Factory Reset 74
5.7. Configuration Management 74
5.8. Firmware Upgrade 76
5.9. User Administration 78
6. System Statistics 80
6.2. Serial Ports Statistics 81
6.3. IP Statistics 81
 ReasmOKs : 83
 ReasmFails : 83
 FragOKs : 83
 FragFails : 83
 FragCreates : 83
6.4. ICMP Statistics 84
6.5. TCP Statistics 86
6.6. UDP Statistics 88
7. CLI Guide 89
7.4. Accessing CLI 90
1 2 3 4 5 91
HelloDevice 92
Remote Host 92
A 1.4. Serial Wiring Diagram 93
A 2.1. port1.conf 95
A 2.2. filter.conf 95
A 2.3. snmp.conf 95
A 4.1. Overview 98
A 4.2. Main Menu 98
A 4.3. RTC Configuration Menu 98
A 4.4. Hardware Test Menu 99
A 4.5. Firmware Upgrade Menu 102
SSL enable = Enable 105
Appendix 6. Warranty 109

Kommentare zu diesen Handbüchern

Keine Kommentare

Sena PS810 Bedienungsanleitung Seite 19

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Computerzubehör Sena PS810