Sena PS810 Bedienungsanleitung Seite 45
- Seite / 110
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
45
2) Operations
Serial data transfer
Whenever the serial device sends data through the serial port of the Pro Series, data will be
accumulated on the serial port buffer of the Pro Series. If the buffer is full or the time gap reaches the
inter-character timeout (See Options in section 4.2.6. Serial Port Parameters for details on inter-
character timeout), the Pro Series connect to the registered remote host(s). If a TCP session has not
been established yet and the Pro Series succeeds in connecting to the remote host, the data in the
serial port buffer will be transferred to the host. Otherwise, all the data stored in the buffer will be
cleared.
Session disconnection
The connected session will be disconnected when the remote host sends disconnection request or
when no data transfer activity is found through the serial port for certain amount of time, which is
“Inactivity timeout”. All the data remained in the serial port buffer will be cleared when it is
disconnected.
Connection request from remote host
All the incoming TCP connection requests will be rejected in TCP client mode.
3) Parameters
TCP listening port
This is the TCP port number through which a remote host can connect a TCP session, and, send and
receive data. Incoming connection request(s) to the ports other than TCP Listening Port will be
rejected. The Pro Series does restrict the port number from 1024 to 65535 and if it is set as 0 only
outgoing connection is permitted. (TCP server mode)
User authentication
If the User authentication option is enabled, the user can access the port after entering the correct
user ID and password. Please refer to the section 5.9. User Administration for details of user
management.
Telnet protocol
In TCP mode, Pro Series supports Telnet Com Port Control Option (RFC2217 compliant) so that user
can control serial parameters like baud rate, data bits and flow control option using his local RFC2217-
compliant Telnet client program. (Please refer to section 4.2.6. Serial Port Parameters for more detail
information about serial parameters)
Usually this option is used with the RFC2217-compliant COM port redirector so that user can control
parameters of serial ports of Pro Series using his serial port application program.
- HelloDevice Pro Series 1
- Copyright Information 2
- Trademark Information 2
- Notice to Users 2
- Technical Support 2
- Revision history 3
- Contents 4
- 5. System Administration 71 5
- 6. System Statistics 80 5
- 7. CLI Guide 89 5
- 1. Introduction 7
- 1.2. Package Check List 8
- 1.3. Product Specification 9
- MAC address 10
- Session 10
- Client/Server 10
- Table 1-1 Acronym Table 11
- 2. Getting Started 12
- 2.1.2. PS410/810 Panel Layout 13
- 2.2. Connecting The Hardware 14
- 2.2.3. Connecting The Power 17
- System console: 18
- Remote console: 18
- 9600 Baud rate 19
- Data bits 8 19
- Parity None 19
- Stop bits 1 19
- No flow control 19
- 2.2.6. Using Remote Console 21
- 3. Network Configuration 24
- IP address 25
- Subnet mask 25
- Default gateway 25
- Primary and Secondary DNS 25
- 3.1.2. Using DHCP 26
- 3.2. SNMP Configurations 27
- 3.2.4. Management Using SNMP 29
- 3.4. SMTP Configuration 31
- 3.5. IP Filtering 32
- Service 33
- Chain rule 33
- 3.7. Locating Server 35
- 3.8. NFS Server Configuration 37
- TCP keep-alive time: 38
- TCP “keep-alive” probes: 38
- TCP keep-alive intervals: 38
- 4. Serial Port Configuration 39
- TCP/UDP mode only 40
- TCP mode only 40
- 4.2.1. Port Enable/Disable 41
- 4.2.2. Port Title 42
- UDP mode 43
- Modem emulation mode 43
- Max. allowed connection 46
- Cyclic Connection 46
- Inactivity Timeout 46
- Socket ID 46
- TCP Nagle algorithm 46
- DTR/DSR behavior 47
- UDP receiving port 49
- (Verbose Code) 51
- * Not supported in PS810 53
- Command echo delay(ms) 55
- Default command echo 56
- Default data mode 56
- Init string 56
- 4.2.6. Serial Port Parameters 62
- Baud rate 63
- Data bits 63
- Parity 63
- Stop bits 63
- Flow control 64
- Inter-character timeout 64
- 4.2.7. Modem Configuration 65
- 4.2.8. Port Logging 67
- Port event handling 68
- Notification interval 68
- Email notification 68
- Subject of Email 68
- Recipient’s Email address 68
- 5. System Administration 71
- 5.3. Change Password 72
- 5.5. Date And Time Settings 73
- 5.6. Factory Reset 74
- 5.7. Configuration Management 74
- 5.8. Firmware Upgrade 76
- 5.9. User Administration 78
- 6. System Statistics 80
- 6.2. Serial Ports Statistics 81
- 6.3. IP Statistics 81
- ReasmOKs : 83
- ReasmFails : 83
- FragOKs : 83
- FragFails : 83
- FragCreates : 83
- 6.4. ICMP Statistics 84
- 6.5. TCP Statistics 86
- 6.6. UDP Statistics 88
- 7. CLI Guide 89
- 7.4. Accessing CLI 90
- 1 2 3 4 5 91
- HelloDevice 92
- Remote Host 92
- A 1.4. Serial Wiring Diagram 93
- A 2.1. port1.conf 95
- A 2.2. filter.conf 95
- A 2.3. snmp.conf 95
- A 4.1. Overview 98
- A 4.2. Main Menu 98
- A 4.3. RTC Configuration Menu 98
- A 4.4. Hardware Test Menu 99
- A 4.5. Firmware Upgrade Menu 102
- SSL enable = Enable 105
- Appendix 6. Warranty 109
Verwandte Produkte und Handbücher für Computerzubehör Sena PS810
Computerzubehör Sena PS210W Bedienungsanleitung
(104 Seiten)
(104 Seiten)
Computerzubehör Sena LS110 Bedienungsanleitung
(66 Seiten)
(66 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.523 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern