Sena PS810 Bedienungsanleitung Seite 12
- Seite / 110
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
12
2. Getting Started
This chapter describes how to set up and configure the Pro Series.
- 2.1 Panel Layout explains the layout of the panel and LED indicators.
- 2.2 Connecting The Hardware describes how to connect the power, the network, and the
equipment to the Pro Series and how to access the console port using a serial console or a
Telnet from remote location..
- 2.3 Accessing The Web Browser Management Interface describes how to access Web menu
from remote location.
The following items are required to get started.
- One power cable (included in the package)
- One Serial data cable (included in the package)
- One Ethernet cable
- One PC with Network Interface Card (hereafter, NIC) and/or one RS232 serial port.
2.1. Panel Layout
2.1.1. PS110 Panel Layout
The PS110 has four LED indicator lamps for status display. Upper-left lamp indicates the system
power-on status. Lower-left lamp indicates the 10/100Base Ethernet Link status. Right two lamps
indicate Receive and Transmit of the serial port.
There is a factory reset switch bottom panel of PS110 and the user can use this switch to restore
factory default configuration.
There is also a DIP switch located next to the Ethernet connector to set communication type of serial
port. (Please refer to Section 4.2.6. Serial Port Parameters and Appendix 1. Connections for more
detail information of serial communication type and its connection)
User can also select console or data mode of serial port using the Data/Console switch located next to
the serial port. (Please refer to Section 2.2.5. Using The System Console for more detail information of
serial console access)
Table 2-1 LED indicator lamps of the PS 110
Lamps Function
Power
Turned on to RED if power is supplied
Status
Ethernet
Ready
Turned on to GREEN if system is connected to Ethernet network.
Rx
Blinks whenever there is any incoming data stream through the serial port of
the PS110
Serial port
Tx
Blinks whenever there is any outgoing data stream through the serial port of
the PS110
- HelloDevice Pro Series 1
- Copyright Information 2
- Trademark Information 2
- Notice to Users 2
- Technical Support 2
- Revision history 3
- Contents 4
- 5. System Administration 71 5
- 6. System Statistics 80 5
- 7. CLI Guide 89 5
- 1. Introduction 7
- 1.2. Package Check List 8
- 1.3. Product Specification 9
- MAC address 10
- Session 10
- Client/Server 10
- Table 1-1 Acronym Table 11
- 2. Getting Started 12
- 2.1.2. PS410/810 Panel Layout 13
- 2.2. Connecting The Hardware 14
- 2.2.3. Connecting The Power 17
- System console: 18
- Remote console: 18
- 9600 Baud rate 19
- Data bits 8 19
- Parity None 19
- Stop bits 1 19
- No flow control 19
- 2.2.6. Using Remote Console 21
- 3. Network Configuration 24
- IP address 25
- Subnet mask 25
- Default gateway 25
- Primary and Secondary DNS 25
- 3.1.2. Using DHCP 26
- 3.2. SNMP Configurations 27
- 3.2.4. Management Using SNMP 29
- 3.4. SMTP Configuration 31
- 3.5. IP Filtering 32
- Service 33
- Chain rule 33
- 3.7. Locating Server 35
- 3.8. NFS Server Configuration 37
- TCP keep-alive time: 38
- TCP “keep-alive” probes: 38
- TCP keep-alive intervals: 38
- 4. Serial Port Configuration 39
- TCP/UDP mode only 40
- TCP mode only 40
- 4.2.1. Port Enable/Disable 41
- 4.2.2. Port Title 42
- UDP mode 43
- Modem emulation mode 43
- Max. allowed connection 46
- Cyclic Connection 46
- Inactivity Timeout 46
- Socket ID 46
- TCP Nagle algorithm 46
- DTR/DSR behavior 47
- UDP receiving port 49
- (Verbose Code) 51
- * Not supported in PS810 53
- Command echo delay(ms) 55
- Default command echo 56
- Default data mode 56
- Init string 56
- 4.2.6. Serial Port Parameters 62
- Baud rate 63
- Data bits 63
- Parity 63
- Stop bits 63
- Flow control 64
- Inter-character timeout 64
- 4.2.7. Modem Configuration 65
- 4.2.8. Port Logging 67
- Port event handling 68
- Notification interval 68
- Email notification 68
- Subject of Email 68
- Recipient’s Email address 68
- 5. System Administration 71
- 5.3. Change Password 72
- 5.5. Date And Time Settings 73
- 5.6. Factory Reset 74
- 5.7. Configuration Management 74
- 5.8. Firmware Upgrade 76
- 5.9. User Administration 78
- 6. System Statistics 80
- 6.2. Serial Ports Statistics 81
- 6.3. IP Statistics 81
- ReasmOKs : 83
- ReasmFails : 83
- FragOKs : 83
- FragFails : 83
- FragCreates : 83
- 6.4. ICMP Statistics 84
- 6.5. TCP Statistics 86
- 6.6. UDP Statistics 88
- 7. CLI Guide 89
- 7.4. Accessing CLI 90
- 1 2 3 4 5 91
- HelloDevice 92
- Remote Host 92
- A 1.4. Serial Wiring Diagram 93
- A 2.1. port1.conf 95
- A 2.2. filter.conf 95
- A 2.3. snmp.conf 95
- A 4.1. Overview 98
- A 4.2. Main Menu 98
- A 4.3. RTC Configuration Menu 98
- A 4.4. Hardware Test Menu 99
- A 4.5. Firmware Upgrade Menu 102
- SSL enable = Enable 105
- Appendix 6. Warranty 109
Verwandte Produkte und Handbücher für Computerzubehör Sena PS810
Computerzubehör Sena PS210W Bedienungsanleitung
(104 Seiten)
(104 Seiten)
Computerzubehör Sena LS110 Bedienungsanleitung
(66 Seiten)
(66 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.469 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern