Sena NEMO10-SK Bedienungsanleitung

1NEMO10 / NEMO10-SKUser GuideVersion 1.4.42011-12-12

10Table 2-1 Pinout for the NEMO10 external interfacePin NO. Description1 GND2 Reset(High Active)3 N.C4 N.C5 LED (Ethernet Link/Collision)6 Ethernet Tx

11Figure 2-1 Layout and dimension of the NEMO102.1.2 Test BedThe NEMO10-SK includes a test bed (carrier board) that provides serial connections to the

12the LED description of the board. The test bed has seven LED indicator lamps for status display. Fourlamps indicate the statuses of 10 Base-T Ethern

13Figure 2-2 Board layout and dimension of the test bed

14Figure 2-3 Picture of the NEMO10 test bed and the NEMO10-SK after the installation2.2 Connecting The HardwareThis section describes how to install t

152.2.1 Install The NEMO10 Onto The Test BedPlug the NEMO10 module onto the test bed. Refer to the Figure 2-4 for the installation.Figure 2-4 Installa

16If any of the above does not happen, the NEMO10 test bed is not properly connected to the Ethernetnetwork.Figure 2-6 Connecting a network cable to t

172.3. Accessing Console PortThere are two ways to access console port of the NEMO10 depending on whether the user is locatedat a local site or a remo

184) Run a terminal emulator program such as HyperTerminal. Set up the serial configurationparameters of the terminal emulation program as follows:960

192.3.2 Using Remote ConsoleThe NEMO10 provides remote console feature via telnet as well as serial console so that users canaccess the NEMO10 at remo

2User Guide for the NEMO10/NEMO10-SKVersion 1.4.4Firmware version 1.4.XPrinted in KoreaCopyrightCopyright 2002~2012, Sena Technologies, Inc. All right

202.4 Command UsageThe NEMO10 provides several simple commands for configuration and control of the NEMO10. Table2-4 summarizes command set which NEMO

21The ‘group’ is the category where the parameters should be entered. For example, if users want to setparameters related to the IP configuration, use

222.4.2 ‘get’ CommandWith ‘get’ command, users can view the current parameter values and status of the NEMO10. Basic‘get’ command usage is as follows:

23--- Host ---Host_mode: tcpsLocal_port: 6001Inactivity_timeout(sec): 300--- Serial ---Baudrate: 9600Data_bits: 8_bitsParity: NoneStop_bits: 1_bitFlow

24> help ipset ip ipmode par1 par2 ...- ipmode: static=Static IP / dhcp=DHCP / pppoe=PPPoE- parameters:if ipmode = static,par1 = IP address,par2 =

252.4.6 ‘exit’ CommandWith ‘exit’ command, current serial or remote console session will be closed. However, changedparameters are not applied until t

263: IP Address ConfigurationA valid IP address of the NEMO10 needs to be assigned before it starts to work in the user's networkenvironment. A n

273.1 Static IP3.1.1 OverviewIn the Static IP mode, users have to manually specify all the parameters such as IP addresses of theNEMO10, valid subnet

28> set ip static 192.168.1.10 255.255.255.0 192.168.1.1OKFigure 3-1 Setting IP configuration parameters for Static IP mode3.2 DHCP3.2.1 OverviewDy

293.2.2 DHCP ConfigurationTo make the NEMO10 work in DHCP mode, just set IP mode to DHCP as in Figure 3-2.> set ip dhcpOK>Figure 3-2 Setting DHC

3Table of Contents1: Introduction 51.1 Overview ...

303.4 IP FilteringThe NEMO10 has an IP address based filtering feature to prevent unauthorized remote hosts fromaccessing NEMO10. The user can allow o

314: Host Mode ConfigurationHost mode represents the operating session mode of the NEMO10. Several host modes are availablefor the data communication

32Basic ‘set’ command usage for host mode configuration is as follows:set host hostmode par1 par2 ...where,hostmode: tcps=TCP server / tcpc=TCP client

33 Sync-SentIf the NEMO10 sends a connection request to a remote host, the state is changed from [Closed]to [Sync-Sent]. This state is maintained unt

342) Operations Serial data transferWhen a session has been established, the NEMO10 reads the data from the serial port buffer tillinternal serial bu

354.1.2 TCP Server Mode ConfigurationTo configure the NEMO10 to work as a TCP server, use ‘set’ command as follows:set host tcps listening_TCP_port in

364.2 TCP Client Mode Operations4.2.1 OverviewThe NEMO10 works as a TCP client, and the default TCP state is [Closed] in this mode. The remotehost wil

37 Cyclic ConnectionIt Cyclic Connection function is enabled, the NEMO10 will make an attempt to connect to theuser-defined remote host at certain in

384.2.2 TCP Client Mode ConfigurationTo configure the NEMO10 to work as a TCP client, use set command as follows:set host tcpc dest_ip dest_port cycli

39[Listen] --> [Sync-Sent] --> [Established] --> [Data] --> [Closed] --> [Listen]The initial state is [Listen]. If there are data comin

44: Host Mode Configuration 314.1 TCP Server Mode Operations...

404.3.2 TCP Server/Client Mode ConfigurationTo configure the NEMO10 to work as a TCP server/client mode, use ‘set’ command as follows:set host tcpsc l

415: Serial Port ConfigurationTo attach the serial device to the NEMO10 serial port, its serial port operation should match exactly tothat of the seri

42The factory default setting of the flow control is None. Only hardware flow control using RTS/CTS issupported by the NEMO10. Hardware flow control m

43> set serial 9600 7 e 2 h s n 10OK>Figure 5-1 Serial port configuration

446: System AdministrationUsers can configure administrator username, password and device name using set command asfollows:set admin username password

45Appendix A: ConnectionsA.1 Ethernet PinoutsThe NEMO10-SK uses standard Ethernet connector, which is a shielded connector compliant withAT&T258 s

46A.3 Ethernet Wiring DiagramFigure A-3 Ethernet direct connection using crossover ethernet cableFigure A-4 Ethernet connection using straight through

47A.5 NEMO10-SK Schematic Diagram

MG8x DESIGN.EL O G I C S L T D .ALL RIGHTS RESERVEDUPDATEESRX/TXDESIGNCHECK-1CHECK-2DATEREMARK4NEMO10_SK2002-08-081/1CABFGND33pF C3REV.5 763 6L

48Appendix B: Well-known Port NumbersThe port numbers are divided into three ranges: the Well Known Ports, the Registered Ports, and theDynamic and/or

51: Introduction1.1 OverviewThe NEMO10 allows you to network-enable a variety of serial devices that were not originallydesigned to have network-capab

49Appendix C: TroubleshootingC.1 Power/LED Status TroubleshootingProblem Cause ActionPower LED doesnot light upPower cable is notconnectedCheck power

50C.3 Remote Console TroubleshootingProblem Cause ActionThe NEMO10 is notassigned valid IPaddressUse serial console to assign valid IP address to the

51C.6 TCP Server Mode Operation TroubleshootingProblem Cause ActionIP configuration ofremote host is invalidCheck if IP configuration of the remote ho

52Appendix D: WarrantyD.1 GENERAL WARRANTY POLICYSena Technologies, Inc. (hereinafter referred to as SENA) warrants that the Product shall conform toa

53D.3 HARDWARE PRODUCT WARRANTY DETAILSWARRANTY PERIOD: SENA warranties embedded hardware Product for a period of one (1) year,and external hardware P

61.2 Package Check List NEMO10NEMO10 DIL module NEMO10-SK- NEMO10 DIL module- Carrier board for the NEMO10- 110V or 230V Power supply adapter- Ether

71.4 Terminologies And AcronymsThe Internetworking related terminologies used frequently in this manual are defined clearly to helpyour better underst

8Table 1-1 Acronym TableISPInternet Service ProviderPCPersonal ComputerNICNetwork Interface CardMACMedia Access ControlLANLocal Area NetworkUTPUnshiel

92: Getting StartedThis chapter describes how to set up and configure the NEMO10 in the first place by using the testbed included in the NEMO10-SK.- 2