Sena PS810 Bedienungsanleitung Seite 52
- Seite / 110
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
52
ATD(T)
[remote IP or domain
name]:[remote
port][CR][LF]
or
ATD(T)
[remote IP][remote port]
[CR][LF]
Set TCP mode as TCP client mode. And then, try to connect
to the specified remote host.
e.g. atdt192.168.1.9:1002
e.g. atdt1921680010091002
Connect to IP address, 192.168.1.9, port 1002
(Port Number is permitted from 1 to 65534)
e.g. atdtps.sena.com:1002
Connect to domain address ps.sena.com, port 1002
ATDR
[remote IP or domain
name]:[remote port]
[CR][LF]
This command is similar to ATD(T). The difference is that
ATDR forces the connection to be Raw TCP connection
regardless of Cryptography configuration and Default Data
mode option.
ATDS
[remote IP or domain
name]:[remote port]
[CR][LF]
This command is similar to ATD(T). The difference is that
ATDR forces the connection to be SSLv3 connection. The
Cryptography configuration should be SSLv3. If not, this
command returns ERROR.
If success,
CONNECT [CR][LF]
If failure in connection,
NO CARRIER [CR][LF]
If other errors,
ERROR [CR][LF]
AT&Tn [CR][LF]
Change and display the default data mode.
AT&T : Display the current Default data mode
AT&T0 : Change the Default data mode to Raw TCP mode
AT&T1 : Change the Default data mode to Telnet binary mode
AT&T
If Data mode=RawTCP
0 [CR][LF]
If Data mode=Telnet
binary
1 [CR][LF]
AT&Tn
If success,
OK[CR][LF]
If failure,
ERROR[CR][LF]
AT orATZ [CR][LF] Initialize TCP socket and serial port
ATA/ [CR][LF] Repeat last command
ATA
[Local port number]
[CR][LF]
Set TCP mode as TCP server mode. And then, set TCP state
as [Listen].
-. If the command parameter, Local port number is not
specified, the TCP session parameter, Local Port is used
instead.
ATAR
[Local port number]
[CR][LF]
This command is similar to ATA. The difference is that ATAR
forces the connection to be Raw TCP connection regardless
of Cryptography configuration and Default Data mode option.
ATAS
[Local port number]
[CR][LF]
This command is similar to ATA. The difference is that ATAS
forces the connection to be SSLv3 connection. The
Cryptography configuration should be SSLv3. If not, this
command returns ERROR.
ATEn [CR][LF]
E, E0: Disable echo
E1: Enable echo
ATOn [CR][LF] O, O0: Turn to data mode
ATQn [CR][LF]
Q, Q0: Response display on (default)
Q1: Response display off
ATVn [CR][LF]
V, V0: Response = <numeric code> [CR][LF]
V1 (default): Response = <verbose code> [CR][LF]
AT&Fn [CR][LF] F, F0, F1: Restore default modem settings
ATHn [CR][LF]
H, H0: Disconnect current TCP connection
All the data will be cleared
H1: Keep the current TCP connection
If success,
OK [CR][LF]
If failure,
ERROR [CR][LF]
- HelloDevice Pro Series 1
- Copyright Information 2
- Trademark Information 2
- Notice to Users 2
- Technical Support 2
- Revision history 3
- Contents 4
- 5. System Administration 71 5
- 6. System Statistics 80 5
- 7. CLI Guide 89 5
- 1. Introduction 7
- 1.2. Package Check List 8
- 1.3. Product Specification 9
- MAC address 10
- Session 10
- Client/Server 10
- Table 1-1 Acronym Table 11
- 2. Getting Started 12
- 2.1.2. PS410/810 Panel Layout 13
- 2.2. Connecting The Hardware 14
- 2.2.3. Connecting The Power 17
- System console: 18
- Remote console: 18
- 9600 Baud rate 19
- Data bits 8 19
- Parity None 19
- Stop bits 1 19
- No flow control 19
- 2.2.6. Using Remote Console 21
- 3. Network Configuration 24
- IP address 25
- Subnet mask 25
- Default gateway 25
- Primary and Secondary DNS 25
- 3.1.2. Using DHCP 26
- 3.2. SNMP Configurations 27
- 3.2.4. Management Using SNMP 29
- 3.4. SMTP Configuration 31
- 3.5. IP Filtering 32
- Service 33
- Chain rule 33
- 3.7. Locating Server 35
- 3.8. NFS Server Configuration 37
- TCP keep-alive time: 38
- TCP “keep-alive” probes: 38
- TCP keep-alive intervals: 38
- 4. Serial Port Configuration 39
- TCP/UDP mode only 40
- TCP mode only 40
- 4.2.1. Port Enable/Disable 41
- 4.2.2. Port Title 42
- UDP mode 43
- Modem emulation mode 43
- Max. allowed connection 46
- Cyclic Connection 46
- Inactivity Timeout 46
- Socket ID 46
- TCP Nagle algorithm 46
- DTR/DSR behavior 47
- UDP receiving port 49
- (Verbose Code) 51
- * Not supported in PS810 53
- Command echo delay(ms) 55
- Default command echo 56
- Default data mode 56
- Init string 56
- 4.2.6. Serial Port Parameters 62
- Baud rate 63
- Data bits 63
- Parity 63
- Stop bits 63
- Flow control 64
- Inter-character timeout 64
- 4.2.7. Modem Configuration 65
- 4.2.8. Port Logging 67
- Port event handling 68
- Notification interval 68
- Email notification 68
- Subject of Email 68
- Recipient’s Email address 68
- 5. System Administration 71
- 5.3. Change Password 72
- 5.5. Date And Time Settings 73
- 5.6. Factory Reset 74
- 5.7. Configuration Management 74
- 5.8. Firmware Upgrade 76
- 5.9. User Administration 78
- 6. System Statistics 80
- 6.2. Serial Ports Statistics 81
- 6.3. IP Statistics 81
- ReasmOKs : 83
- ReasmFails : 83
- FragOKs : 83
- FragFails : 83
- FragCreates : 83
- 6.4. ICMP Statistics 84
- 6.5. TCP Statistics 86
- 6.6. UDP Statistics 88
- 7. CLI Guide 89
- 7.4. Accessing CLI 90
- 1 2 3 4 5 91
- HelloDevice 92
- Remote Host 92
- A 1.4. Serial Wiring Diagram 93
- A 2.1. port1.conf 95
- A 2.2. filter.conf 95
- A 2.3. snmp.conf 95
- A 4.1. Overview 98
- A 4.2. Main Menu 98
- A 4.3. RTC Configuration Menu 98
- A 4.4. Hardware Test Menu 99
- A 4.5. Firmware Upgrade Menu 102
- SSL enable = Enable 105
- Appendix 6. Warranty 109
Verwandte Produkte und Handbücher für Computerzubehör Sena PS810
Computerzubehör Sena PS210W Bedienungsanleitung
(104 Seiten)
(104 Seiten)
Computerzubehör Sena LS110 Bedienungsanleitung
(66 Seiten)
(66 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.224 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern