Sena SPH10H-FM Betriebsanweisung

Sena Bluetooth Pack for GoPro®User's Guide

10Power SwitchMic SwitchAudio SourceOO NoneOnInternal microphone of the Bluetooth PackOnOMicrophone of Bluetooth headsetOnInternal microphone of t

11EnglishLED Status4 ashesHigh, 70 to 100 % remaining battery3 ashesMedium, 30 to 70 % remaining battery2 ashes Low, 0 to 30 % remaining batteryPr

12Factory ResetThrough the factory reset, you can restore the factory default settings of the Bluetooth Pack. Then all of the previous pairing informa

13English4. OPERATIONHeadset Audio Recording ModeMic SwitchApplicationSena Single voiceUltra HD Voice Recording™O• CD-quality voice recording without

14Pairing with HeadsetsTo record your voice to the GoPro® by using the Bluetooth Pack, you should pair the Bluetooth Pack with a Bluetooth headset (or

15EnglishFor Non-Sena Headsets1Press and hold the Pairing Button of the Bluetooth Pack for 5 seconds until the LED ashes red and blue alternately.2En

16For Sena HeadsetsYou can connect the Bluetooth Pack with Sena headsets and transfer the conversations to the Bluetooth Pack by establishing intercom

17EnglishFirst Friend (B)You (A)Bluetooth Pack (A)Bluetooth Pack (B)Dual Bluetooth Pack Connection for Sound Sharing For Non-Sena HeadsetsYou can conn

18Ultra HD Voice Recording™ Mode & Normal Voice Recording ModeWhen using a Sena headset, Ultra HD Voice Recording™ is supported; it enables you to

19EnglishSidetone SettingWhen using a Sena Headset, you can enable or disable the sidetone function while the audio channel between the Bluetooth Pack

© 1998-2014 Sena Technologies Inc. All rights reserved.Sena Technologies Inc. reserves the right to make any changes and improvements to its product w

20Firmware Upgrade The Bluetooth Pack supports rmware upgrade function. Please visit Sena Bluetooth web site at www.SenaBluetooth.com to check the la

21EnglishType Operation Button Duration LEDTransmitting Voice Signals for Sena HeadsetsUltra HD Voice RecordingTM Mode/ Normal Voice Recording toggleP

226. SPECIFICATIONSGeneralTalk time 3 hoursStand-by time 3 daysOperating temperature -10˚C ~ 55˚C (14°F ~ 131°F)Dimensions (main module)59 mm x 41 mm

23EnglishBATTERY INFORMATIONThe product has an internal, non-removable, rechargeable battery. Do not attempt to remove the battery from the device as

24DISPOSAL The crossed-out wheel bin symbol on the product, literature, or packaging reminds you that all electrical and electron

25Englishharmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to

26Industry Canada StatementThis device complies with Industry Canada license-exempt RSS standard(s).Operation is subject to the following two conditio

27EnglishLimited warranty service may be obtained by delivering the Product to Sena or to the international distributor it was purchased through and p

www.SenaBluetooth.comUser's Guide for Firmware v1.01.0.0

3EnglishCONTENTS1. INTRODUCTION ...42. PACKAGE CONTENTS ...5Bluetooth Pac

41. INTRODUCTIONThank you for choosing the Sena Bluetooth Pack for GoPro®. The Sena Bluetooth Pack for GoPro® is a specially designed adapter for the

5English2. PACKAGE CONTENTSBluetooth Pack<Rear><Front>Power Switch Internal Stereo MicrophonesReset Pin HoleMic SwitchStatus LEDPairing B

63. GETTING STARTEDAttaching the Bluetooth Pack to the GoPro®1Slide the hooked end of the Bluetooth Pack into the groove on the right side of the came

7EnglishRemoving the Bluetooth Pack from the GoPro®1Remove the Audio Connector.2Pull back on left side of the Bluetooth Pack to disconnect from the Go

8Installing the Case1Align the Audio Connector with the space on the frame.2Lift up the frame case slightly and slide the assembled camera into the fr

9English3You can mount the assembled frame case to helmets, vehicles, and other gears by using the GoPro® accessories: Attachment Buckle and Thumb Scr