Sena ProBee-ZS10 Betriebsanweisung

1ProBee-ZS10 User Guide Rev.1.1.1ZigBee Serial AdapterProBee-ZS10User GuideSena Technologies, Inc.Rev 1.1.1

10ProBee-ZS10 User Guide Rev.1.1.12 Getting StartedCreating a ZigBee network using the ZS10 adapters consists of the following steps: Connect a power

11ProBee-ZS10 User Guide Rev.1.1.12.1.2 Connecting the panelPlease connect the device to your computer directly or using serial cable so AT commands c

12ProBee-ZS10 User Guide Rev.1.1.12.1.4 Attaching Battery Pack to ZS10The ZS10 also supports optional standard battery pack (240mAh) and extended batt

13ProBee-ZS10 User Guide Rev.1.1.1Step2. Slide the battery pack into the ZS10 slot.Figure 2-6 Attach the battery packStep3. Fasten the battery pack to

14ProBee-ZS10 User Guide Rev.1.1.1blink periodically. Please refer to 7 S-Registers for S14 regarding the management ofthe LED status.Status Status LE

15ProBee-ZS10 User Guide Rev.1.1.1parity, stop bit and flow control option. If the baud rate needs to a baud rate not shown below, ProBeeManager or te

16ProBee-ZS10 User Guide Rev.1.1.1Figure 2-9 HyperTerminal Serial SettingsTo display the AT commands that are being typed, you need to enable the loca

17ProBee-ZS10 User Guide Rev.1.1.12.4 Using ProBee Manager for ConfigurationFigure 2-11 ProBee ManagerIt is possible to set or get the configurations

18ProBee-ZS10 User Guide Rev.1.1.13 ZigBee Network ConfigurationA ZigBee Network consists of a coordinator, routers and end devices. A minimal ZigBee

19ProBee-ZS10 User Guide Rev.1.1.1 Configure the ZS10 node type as the coordinator Optionally, select the channel mask. Otherwise, the ZS10 will use

2ProBee-ZS10 User Guide Rev.1.1.1ProBee-ZS10 User GuideFirmware version PTv1.XCopyrightCopyright 2011 Sena Technologies, Inc. All rights reserved.Sena

20ProBee-ZS10 User Guide Rev.1.1.1Table 3-2 Channel BitmaskChannel 12 13 14 15 16 17 18Bit mask 00001000 00002000 00004000 00008000 00010000 00020000

21ProBee-ZS10 User Guide Rev.1.1.1The user can permit joining for a moment at need. The AT command to permit joining isAT+PERMIT=n or AT+PJ=nWhere n i

22ProBee-ZS10 User Guide Rev.1.1.1Example)AT+NODETYPE=2<CR> # Select router modeOK<CR> # ResponseATZ<CR> # Apply the changeOK<CR&

23ProBee-ZS10 User Guide Rev.1.1.13.3 Setting up ZS10 as an End DeviceAn end device is a leaf node which communicates only with its parent node and wi

24ProBee-ZS10 User Guide Rev.1.1.1the ZigBee network found automatically. Configure the settings for sleep interval.Please refer to the section 3.2 S

25ProBee-ZS10 User Guide Rev.1.1.1Figure 3-1 Sleep Interval and Wake-up TimingThe sleepy end device can also wake up from the sleep mode by function b

26ProBee-ZS10 User Guide Rev.1.1.13.5.1 Security LevelIn order to use security in the application, a user should set security level using the AT comma

27ProBee-ZS10 User Guide Rev.1.1.14 Data TransmissionThe ZS10 supports three different types of data transmissions: unicast, multicast and broadcast.

28ProBee-ZS10 User Guide Rev.1.1.1ATS36=n, where n is the radius.ATS37=n, where n is the number of hops through nonmembers.4.1.3 BroadcastBroadcast tr

29ProBee-ZS10 User Guide Rev.1.1.1the data mode, on the other hand, incoming data is always displayed. To change the S11 register, pleaseuse the AT co

3ProBee-ZS10 User Guide Rev.1.1.1Contents1 INTRODUCTION ...

30ProBee-ZS10 User Guide Rev.1.1.1ATD<CR>Set unicast data mode to the preconfigured destination IEEE address without reset.ATD<value><C

31ProBee-ZS10 User Guide Rev.1.1.1AT+TRANSMITMODE=1<CR> # Set transmit mode to destination IEEE addressOK<CR> # ResponseATZ<CR> # Ap

32ProBee-ZS10 User Guide Rev.1.1.1Set multicast data mode to preconfigured destination group ID without reset.ATM<value><CR>Set multicast

33ProBee-ZS10 User Guide Rev.1.1.14.2.3 Broadcast Data ModeBroadcast data mode can be used for continuous data transmission to all devices in the curr

34ProBee-ZS10 User Guide Rev.1.1.1ATZ<CR> # Apply to changeOK<CR> # ResponseSend broadcast msg # Put the broadcast message+++ # Leave data

35ProBee-ZS10 User Guide Rev.1.1.15 AT Command Reference5.1 Command Line FormatEach command line is composed of a prefix, body and terminator. Only “A

36ProBee-ZS10 User Guide Rev.1.1.15.2.4 ATEDescription Echo(1) or No Echo(0).Execute ATE<number><CR>Response OK<CR>5.2.5 ATMDescript

37ProBee-ZS10 User Guide Rev.1.1.15.2.11 +++Description Interrupt data mode. “+++”must be entered within 500ms.Execute +++Response OK<CR>5.3 Nod

38ProBee-ZS10 User Guide Rev.1.1.15.3.5 AT+OPPANID or AT+OIDescriptionGet the operating 16-bit PAN ID. If PAN ID is set specific value not 0s, operati

39ProBee-ZS10 User Guide Rev.1.1.1Range 00001000 - 03FFF0005.4.2 AT+PANID or AT+PIDescriptionGet/Set the 16-bit PAN ID. If it is set to 0s, the coordi

4ProBee-ZS10 User Guide Rev.1.1.14 DATA TRANSMISSION... 274.1

40ProBee-ZS10 User Guide Rev.1.1.1that should join the same network. (0: Network specific, 1: ZigBee, 2: ZigBee Pro)Execute AT+STACK?<CR> AT+STA

41ProBee-ZS10 User Guide Rev.1.1.1AT+DSCAN=<scan duration><CR> orAT+DSCAN=<scan duration>,<node type><CR> orAT+DSCAN=<

42ProBee-ZS10 User Guide Rev.1.1.1Response<IEEE address><CR>OK<CR>5.6.3 AT+PARENTSA or AT+PSDescription Get the 16-bit Node ID of th

43ProBee-ZS10 User Guide Rev.1.1.15.7.4 AT+MAXPAYLOAD or AT+MPDescriptionGet the maximum size of the payload that the Application Support sub-layer wi

44ProBee-ZS10 User Guide Rev.1.1.1available remote command by “AT+REMOTE<CR>”.Execute AT+REMOTE=<addr>,<cmd>?<CR> AT+REMOTE=&l

45ProBee-ZS10 User Guide Rev.1.1.15.8.5 AT+FLOWCTRL or AT+UFDescription Get/Set flow control status. (0: none, 1: software, 2: hardware flow control)E

46ProBee-ZS10 User Guide Rev.1.1.1Response OK<CR> or ERROR<CR>5.10 Firmware Upload and Help5.10.1 AT+BOOTLOAD or AT+BLDescriptionStart boo

47ProBee-ZS10 User Guide Rev.1.1.16 AT Command Examples6.1 Network configuration6.1.1 CoordinatorAT+NODETYPE=1<CR> # set node type (coordinator)

48ProBee-ZS10 User Guide Rev.1.1.100019500002FDC15OK # ResponseAT+REMOTE=1FEF,AT+LONGADDR<CR> # get 64-bit address of remote node (1FEF)00019500

49ProBee-ZS10 User Guide Rev.1.1.1OK # ResponseMSG06+++ # send data(MSG06) and leave data modeATD00019500002FDC40<CR> # enter the unicast mode u

5ProBee-ZS10 User Guide Rev.1.1.15.4.5 AT+POWER or AT+PW...

50ProBee-ZS10 User Guide Rev.1.1.16.4 SecurityAT+SECURITY=1<CR> # set security level (ON)OK # ResponseAT+LINKKEY=5A46…21<CR> # set the 128

51ProBee-ZS10 User Guide Rev.1.1.16.5.3 Clone# clone the firmware of the local node to a remote node using 64-bit longaddress. Note that UART of local

52ProBee-ZS10 User Guide Rev.1.1.17 S-RegistersRegister number Descriptions111213142122233132333435363738395152535455566162Display incoming message in

53ProBee-ZS10 User Guide Rev.1.1.17.1.2 S12Description Get/Set the command echo mode.Execute ATS12?<CR> ATS12=<value><CR>Response<

54ProBee-ZS10 User Guide Rev.1.1.17.2.2 S22DescriptionGet/Set the timeout to permit joining. It determines the time in seconds that the devicewill all

55ProBee-ZS10 User Guide Rev.1.1.1Range 0 – 997.3.3 S33DescriptionGet/Set the transmission timeout in milliseconds. If application-ACK is enabled, ase

56ProBee-ZS10 User Guide Rev.1.1.1converted to maximum value(30). It is used to multicast/broadcast.Execute ATS36?<CR> ATS36=<value><CR

57ProBee-ZS10 User Guide Rev.1.1.1device does not send a poll request to its parent coordinator or router within the polltimeout, the end device is re

58ProBee-ZS10 User Guide Rev.1.1.17.4.5 S55DescriptionGet/Set the rejoin timeout. If it is enabled, an end-device tries to rejoin the currentnetwork w

59ProBee-ZS10 User Guide Rev.1.1.1Range 0 – 10000

6ProBee-ZS10 User Guide Rev.1.1.16 AT COMMAND EXAMPLES... 476.1 Networ

60ProBee-ZS10 User Guide Rev.1.1.18 Mechanical Drawings8.1 ProBee-ZS10 mechanical drawing (mm)99.8 with stub antenna1673.9 without antenna14.930.820

61ProBee-ZS10 User Guide Rev.1.1.18.2 Battery pack mechanical drawing (mm)Standard Battery PackExtended Battery Pack

62ProBee-ZS10 User Guide Rev.1.1.19 Warranty9.1 GENERAL WARRANTY POLICYSena Technologies, Inc. (hereinafter referred to as SENA) warrants that the Pro

63ProBee-ZS10 User Guide Rev.1.1.1external hardware Product for a period of three (3) or five (5) years according to the Product type.WARRANTY PROCEDU

64ProBee-ZS10 User Guide Rev.1.1.110 Regulatory Information10.1 FCCFCC Rule: Part 15 Subpart C Section 15.247FCCID: S7AZBLINXZS10FCC Compliance Statem

65ProBee-ZS10 User Guide Rev.1.1.1 ProBee-ZS10 ZigBee Serial Adapterto which this declaration relates is in conformity with the following standard(s)

66ProBee-ZS10 User Guide Rev.1.1.111 RF InformationRadio Frequency Range2.410~2.475GHzNumber of Frequency Channel14 channelsTransmission MethodDSSS (D

7ProBee-ZS10 User Guide Rev.1.1.17.4.3 S53...

8ProBee-ZS10 User Guide Rev.1.1.11 Introduction1.1 About This DocumentThis document provides an introduction on configuration and operation of the Pro

9ProBee-ZS10 User Guide Rev.1.1.1Applications Advanced Metering Infrastructure Home Area Networks (HAN) Neighborhood Area Networks (NAN) Home Aut